garyslake
-
- Posts: 4927
- Joined: Fri Sep 20, 2013 8:29 pm
Not sure if mine is any better but I will tell everyone...
You should attempt this image especially in LAB. There is a lot of color information in here..almost every color could use a contrast boost type separation to broaden the range in the image.
I have posted my ACV file but I also made a layer copy and applied it back using soft light as the layer style and reduced the opacity until I was satisfied with the haze in the hills.
This might be a good CMYK candidate as well...
You should attempt this image especially in LAB. There is a lot of color information in here..almost every color could use a contrast boost type separation to broaden the range in the image.
I have posted my ACV file but I also made a layer copy and applied it back using soft light as the layer style and reduced the opacity until I was satisfied with the haze in the hills.
This might be a good CMYK candidate as well...
-
- Posts: 4927
- Joined: Fri Sep 20, 2013 8:29 pm
-
- Posts: 4927
- Joined: Fri Sep 20, 2013 8:29 pm
Greg!
Loaded the acv file. You have set quite som points in the center of the Lab, a and b curves, in a narrow area and adjusted them. Do not quite understand how you placed them and why exactly that adjustments? Assume on a higher level. Only learned that if curves horisontal you will get grey area, or?
Thomas
Loaded the acv file. You have set quite som points in the center of the Lab, a and b curves, in a narrow area and adjusted them. Do not quite understand how you placed them and why exactly that adjustments? Assume on a higher level. Only learned that if curves horisontal you will get grey area, or?
Thomas
In this particular image the colors live in a fairly narrow band near the center of the A and B channels. The idea is to put control points "Contrast Pins" on the curve and separate them vertically. The A channel in this image needs less help than the B channel.
Each point is addressing a separate color issue..Some may be useless but they are added for control and to keep the adjustment from spreading across the entire curve.
If I rotate the curve to horizontal I get muted colors.
If I rotate them to the vertical I get saturated colors.
If I take two points on the curve in the yellow range for instance...see shot attached...and I separate them vertically the "local color" gets more variation and saturation.
To do this: 1) select the first point with the mouse and then 2) hold down the Ctrl key and select the second point. You will have created a "contrast pin" manually and you can rotate them using the side frame of the curve or you can move them around together to change the color balance a bit.
Play around and see what can happen. If you are in the A channel and the Reds get to vibrant you can mute then a bit this way as well...
Greg
Each point is addressing a separate color issue..Some may be useless but they are added for control and to keep the adjustment from spreading across the entire curve.
If I rotate the curve to horizontal I get muted colors.
If I rotate them to the vertical I get saturated colors.
If I take two points on the curve in the yellow range for instance...see shot attached...and I separate them vertically the "local color" gets more variation and saturation.
To do this: 1) select the first point with the mouse and then 2) hold down the Ctrl key and select the second point. You will have created a "contrast pin" manually and you can rotate them using the side frame of the curve or you can move them around together to change the color balance a bit.
Play around and see what can happen. If you are in the A channel and the Reds get to vibrant you can mute then a bit this way as well...
Greg
-
- Posts: 4927
- Joined: Fri Sep 20, 2013 8:29 pm
-
- Posts: 4927
- Joined: Fri Sep 20, 2013 8:29 pm
Return to “Curvemeister 101 January 2009”
Who is online
Users browsing this forum: No registered users and 0 guests